FIX MACARD WIFI EXTENDER NO INTERNET CONNECTION FAST

Fix Macard WiFi Extender No Internet Connection Fast

Fix Macard WiFi Extender No Internet Connection Fast

Blog Article

If you're experiencing the "no internet" problem with your Macard WiFi extender, you're not alone. In this guide, we'll walk you through the common reasons for this issue and provide simple solutions to get your WiFi extender back online.

Why Your Macard WiFi Extender Might Have No Internet

Here are some possible reasons why your Macard WiFi extender isn't providing internet:

Signal Interference: The extender signals might be disrupted.

Connection to the Router: The extender may not be properly connected to your main router.

Software Issues: Glitches or bugs within the device.

ISP-related Problems: Sometimes the issue stems from the Internet Service Provider.

Let's explore the solutions to resolve this issue.

How to Fix the "No Internet" Problem on Your Macard WiFi Extender

The following troubleshooting steps are effective and have been tested to fix the "no internet" issue on your Macard WiFi extender.

1. Reconnect the Extender to the Router


  • To re-establish a connection between your extender and router:

  • Power off the extender and router.

  • Reconnect the extender to the router via WPS or the interface method.


If you're using WPS:

  • Press the WPS button on the extender.

  • Press the WPS button on the router.

  • Wait for the devices to establish a connection, then join the extended network.


If you're using the interface:

  • Connect a computer to the extender's WiFi network.

  • Open a browser and visit Go.macard.online.

  • Log into the interface, then follow the steps to connect the extender to your router.


2. Check the Ethernet Cable (If Applicable)

If you're using an Ethernet cable to link your extender and router, ensure the cable is in good condition. Look for any cuts or wear. If damaged, replace it with a new cable.

3. Verify the Router-to-Modem Connection

Ensure that your router is properly connected to the modem via the Ethernet cable. Double-check that the cable is plugged into the correct ports on both devices. Inspect the cable for any damage.

4. Update the Extender’s Firmware

  • Sometimes, outdated firmware can cause connectivity issues. To update the firmware:

  • Log into the extender's interface by visiting Go.macard.online.

  • Go to the Settings section, then select the Firmware tab.

  • Click Check for Updates. If an update is available, click Install to update the extender.


5. Reboot the Extender

  • Rebooting the extender can often resolve connectivity problems:

  • Press the power button on the extender twice to restart the device.

  • The extender will disconnect and reconnect, rebooting in the process.


6. Reset the Macard WiFi Extender

If none of the previous steps work, try resetting the extender to its factory settings. This will erase all current configurations, so you’ll need to set it up again afterward.

To reset the extender:

  1. Locate the Reset button (usually a small pinhole).

  2. Use a paperclip or pen to press and hold the button for 8 seconds.

  3. Release the button and wait for the extender to reboot.


After the reset, follow these steps to reconfigure the device:

  • Connect a computer to the extender’s WiFi network.

  • Open a browser and visit Go.macard.online.

  • Log in using the default admin credentials.

  • Select the host router's network and enter the password to connect.

  • Set a new SSID (WiFi name) and password for the extended network.

  • Click Save, and the new WiFi network should appear in your devices' WiFi list.


Conclusion

This guide has walked you through the common causes of the "no internet" issue on your Macard WiFi extender and provided easy solutions to get your device back online. If you’re still having trouble, don’t hesitate to contact support for further assistance.

FAQs

1. How to Log Into the Macard WiFi Extender?

To access the extender’s settings, go to Go.macard.online or use the IP address 192.168.10.1. Connect your computer to the extender’s network, then enter either the URL or IP address in your browser. Afterward, log in with the default admin password.

2. How to Connect to the Macard WiFi Extender?

To connect to the Macard WiFi extender’s network, open your device’s Wi-Fi settings and select the extender’s SSID. When prompted, enter the security key, then click Connect.

3. How to Reset the Macard WiFi Extender?

To reset the extender, press and hold the Reset button (pinhole) for 8 seconds using a paperclip or pen. Release it, and the device will reset. You’ll need to set it up again by logging into the extender’s interface and following the configuration steps.

Report this page